Ham Radio Antenna

Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit

Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit
Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit
Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit
Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit
Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit

Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit
HEAVY DUTY HAZER TRAM SYSTEM. Hazers eliminate tower climbing, allow easy access to antennas, carry heavy loads, and feature quality. Construction and easy installation on an erect tower. Never climb a tower again! See below for details on how Hazers work. Dead Weight Load: 150 lbs.

Dimensions: 31" H x 15-1/4" W. Top & bottom plates for rotor and thrust bearing (fits HyGain & Yaesu Rotors).

100' of 1/8 winch cable (for a 50' tower). All mounting hardware (stainless steel). Towers over 50' require additional cabling. Towers equipped with a TailTwister rotor require a HR-6010 TailTwister plate.

Visit our store for more Hazers & Hazer Accessories. HR-2040 ROLLER BEARING SET SPECIFICATIONS. This roller bearing set modifies the Hazer so that it glides up and down the tower using wear-resistant plastic wheels.

This improves the Hazer's performance and eliminates any wear on your tower. The bearing allows a smooth pass over tower joints. Premium weatherized thrust bearing for use when a rotator is used on Hazer system.

Supports and protects rotator from excessive wear. 4 set screws lock the mast in place. Die cast aluminum housing with painted finish. The Hazer works like a simple elevator designed to easily raise and lower your antennas, measuring instruments. The Hazer is designed to wrap around the tower. A pulley at the top of the tower, along with a winch.

And wire rope is used to raise and lower the antenna. It's as simple as raising a flag up a flag pole.

The Hazer makes servicing your antennas a cinch, even with one person! May guy wires be used with the Hazer? A fifty foot tower will require only one set of guy wires in most cases. We suggest putting these guys at the very. Top of the tower in the few inches just above the Hazer.

To lower a beam antenna, disconnect two guys by. Completely unscrewing the turnbuckles at the ground.

The guys then will drape in toward the tower. Then be lowered to the ground. Once down, the guys can be reconnected. Imagine having a completely guyed.

Tower with your antenna system parked at ground level. Never worry about storms again! Is it easy to install? The Hazer is easily assembled on an erected tower; however, some climbing is necessary to install the pulley.

Block assembly and winch cable. If it is installed before the tower is erected, no climbing is required. Installed, the Hazer travels smoothly past tower braces and section joints. As of August 22, 2016 Glen Martin has dropped the MSRP of their H-3 Hazer Systems. GLEN MARTIN HAZER PRODUCTS ARE PROUDLY MADE IN THE USA.

The item "Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit" is in sale since Thursday, September 29, 2016. This item is in the category "Consumer Electronics\Radio Communication\Antennas\Ham, Amateur Radio Antennas". The seller is "antennapartsoutlet1" and is located in Mount Carroll, Illinois. This item can be shipped to United States, to Canada, to United Kingdom, DK, RO, SK, BG, CZ, FI, HU, LV, LT, MT, EE, to Australia, GR, PT, CY, SI, to Japan, to China, SE, KR, ID, to Taiwan, ZA, TH, to Belgium, to France, to Hong Kong, to Ireland, to Netherlands, PL, to Spain, to Italy, to Germany, to Austria, IL, to Mexico, to New Zealand, SG, to Switzerland, NO, SA, UA, AE, QA, KW, BH, HR, BR, CL, CO, CR, PA, TT, GT, HN, JM.
  • To Fit: ROHN 20 / 25 Tower, 20 / 25G ROHN Tower
  • Compatible Brand: Glen Martin Hazer
  • Brand: Glen Martin Hazer
  • Model: Hazer Tram System
  • MPN: H-3 / H3
  • Country/Region of Manufacture: United States
  • Country of Manufacture: United States

Bundle Pack Glen Martin H-3 Hazer, TB-25 Bearing, & HR-2040 Roller Bearing Kit