MR300 Bluetooth Digital Shortwave Antenna Analyzer Meter Tester 1-60M Ham Radio

MR300 Bluetooth Digital Shortwave Antenna Analyzer Meter Tester 1-60M Ham Radio. The item is not included Built-in battery, Does not support Bluetooth. 100% Brand New And High Quality.

Radio enthusiasts an essential tool for entry. Test the antenna technical parameters. Can test the standing wave, impedance, capacitance and so on. Can be connected to the computer to do antenna and other graphic analysis. Power supply: External: 13.8 to 19 Volts DC, 500mA; Internal: 8xAAA 1000mAh NiMH cells.

Charging time: 12 hours (charge rate 0.1C). SWR, impedance (resistance + reactance), capacitance, inductance. Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance). Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance.

12V - Driveable talent works, but can not charge the battery. 3.8V 18V - can drive the talent to work normally, can also be normal for the battery charge. Spectral Purity: Harmonics down Greater than - TBD dB beyond 60 MHz. Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz.

SWR: 1.0 to 9.99. RF Output: Adjustable: 2.0 Volts pp (typ).

Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down". External power: 2.1mm Power Jack (center pin positive). Measure ground loss: Adjust antenna tuners and determine loss. Determine characteristic impedance of transmission line. Determine length of ¼ and ½ wave phasing lines.

1PCMR300 Digital Shortwave Antenna Analyzer Meter Tester. Because of the airspace controls. Note : the item is not included Built-in battery, IT support Bluetooth. Radio enthusiasts an essential tool for entry Test the antenna technical parameters Can test the standing wave, impedance, capacitance and so on Can be connected to the computer to do antenna and other graphic analysis Test frequency: 1-60M Size: 90mm 82mm 30mm Connector: M head Power requirements: within the positive external 12V - Driveable talent works, but can not charge the battery. 13.8V 18V - can drive the talent to work normally, can also be normal for the battery charge.

Specifications 1 Frequency Generation & Control: o 1 - 60 Mhz o Source impedance: 50 Ohms o Stability: +/- 100 ppm o Spectral Purity: Harmonics down >- TBD dB beyond 60 MHz o Step Size: User configurable increments of 100 Hz, 1 kHz, 10 kHz, and 100 kHz Usable Measurement Range: o SWR: 1.0 to 9.99 o Impedance: approx. 5 to 2000 ohms RF Output: o Adjustable: 2.0 Volts pp (typ) Power supply: o External: 13.8 to 19 Volts DC, 500mA o Internal: 8xAAA 1000mAh NiMH cells o Charging time: 12 hours (charge rate 0.1C) 2 Controls: o Pushbuttons (5): "Mode", "Band", "Config", "Scan", "Up", "Down" o Switch: "Power On" Connectors: o RF Out: BNC o USB: Mini-B receptacle o External power: 2.1mm Power Jack (center pin positive) 3 Instrument Capabilities: o Measure antenna electrical parameters: SWR, impedance (resistance + reactance), capacitance, inductance o Measure feedpoint impedance o Measure ground loss Adjust antenna tuners and determine loss o Measure inductors and capacitors o Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance) o Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance o Determine characteristic impedance of transmission line o Determine length of ¼ and ½ wave phasing lines o Coaxial Cable Loss o Determine antenna tuner loss o Measure balun loss o Measure inductor Q o Estimate quartz crystal parameters Adjust antenna tuners and determine loss o Measure inductors and capacitors o Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance) o Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance o Determine characteristic impedance of transmission line o Determine length of ¼ and ½ wave phasing lines o Coaxial Cable Loss o Determine antenna tuner loss o Measure balun loss o Measure inductor Q o Estimate quartz crystal parameters Adjust antenna tuners and determine loss o Measure inductors and capacitors o Measure coax transmission line (SWR, length, velocity factor, approximate Q and loss, resonant frequency, and impedance) o Measure and determine optimum settings for tuning stubs: SWR, approximate Q, resonant frequency, bandwidth, impedance o Determine characteristic impedance of transmission line o Determine length of ¼ and ½ wave phasing lines o Coaxial Cable Loss o Determine antenna tuner loss o Measure balun loss o Measure inductor Q o Estimate quartz crystal parameters Package Included: 1PCMR300 Bluetooth Digital Shortwave Antenna Analyzer Meter Tester 1-60M Ham Radio.

If you have got the package, please confirm. Your Satisfaction is our Priority. Our goal is to make all our customers as happy as possible while shopping with us. We believe our items are so outstanding. If you do not satisfy with our items.

Please simply return to us within 30 Days in original condition. The item "MR300 Bluetooth Digital Shortwave Antenna Analyzer Meter Tester 1-60M Ham Radio" is in sale since Wednesday, July 12, 2017.

This item is in the category "Business & Industrial\Test, Measurement & Inspection\Other Test, Measurement & Inspection". The seller is "diybox" and is located in ShenZhen.

This item can be shipped worldwide.

Brand: Unbranded/Generic
MPN: Does Not Apply
Type: MR300 Antenna Analyzer
Country/Region of Manufacture: China
UPC: Does Not Apply
EAN: Does Not Apply