Ham Radio Antenna

TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts

TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts
TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts

TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts

NEEDS 4 FOOT WHIP TO OPERATE 1.8 TO 30 MHZ. Whip Length versus Frequency Coverage. - 1.8 MHz to 30.0 MHz 5 ft. - 1.7 MHz to 29.0 MHz 6 ft. 1.6 MHz to 28.0 MHz 8 ft.

1.5 MHz to 20.0 MHz 12 ft. 1.2 MHz to 15.0 MHz Packing List for Model 300A: Model 300A Antenna MT1 MOUNT with all hardware Up/Down Switch 20 ft. Control Cable Ferrite Core Fuse Holder & Fuse 1 tube of Dielectric Compound ManualModel 300A Antenna Specifications Lower Mast Length 3ft. Typical SWR 1.5 to 1 or less Total Height with 6 whip at 29 MHz 94 Total Height with 6 whip at 1.7 MHz 114 Weight 8.5 lbs. When properly installed on your vehicle the Model 300A will provide continuous coverage from 1.7 to 28 MHz with a 6' whip. All of our antennas come with the sensors already pre-installed so if you decide to add one of the auto controllers (SDC-100 Simple Controller, SDC-102 Programmable Controller, Turbo Tuner) now or later everything is ready. What makes our antennas stand above the rest is all of our CNC machined components are either aircraft aluminum or stainless steel and blueprinted, meaning you can take 100 antennas apart and mix up the parts then reassemble them and they all work the same. Our coil form is approximately 2 in diameter and made of fiberglass.

The other antenna builders know fiberglass is better but they choose not to use it because of the expense and difficulty in machining. The decoupler we use is CNC machined for tight tolerances with custom fingerstock designed to contact 3 turns of coil all the time with over 25 lbs. With this design you can run up to 250 watts P. It's so superior to anything else on the market.

The Pittman 12 volt commercial grade gear motor is very durable and very quiet while receive tuning. Our weather shield is made of Lexan. This is the same stuff used on racecar windshields and even used to make bulletproof windows.

The Model 300A uses the Dupont Imron 5000 or Powder Coat Paint System. And folks this is not spray paint in a can. With this you get a finish that looks as glossy and last as long as the paint on a new vehicle.

That's just some of the effort that goes into a Tarheel Antenna. You won't be disappointed, I GUARANTEE IT! The antenna is a plug & play system. Included is the antenna, manual switch box, 20 ft. Of control cable, ferrite decoupling core, 3/8-24 stud, connectors, fuseholder and fuse.

Whip Length versus Frequency Coverage 4 ft. 1.2 MHz to 15.0 MHz. Listing and template services provided by inkFrog. The item "TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts" is in sale since Thursday, February 27, 2020. This item is in the category "Consumer Electronics\Radio Communication\Antennas\Ham, Amateur Radio Antennas".

The seller is "2way-radioexpress" and is located in Athens. This item can be shipped worldwide.

  • Model: 300A
  • Type: Antenna
  • MPN: Does Not Apply
  • Brand: Tarheel


TARHEEL 300A SCREWDRIVER ANTENNA, with MT1 Mount, 1.8 to 30 MHz, 250 Watts