Ham Radio Antenna

Glen Martin H-2 Heavy Duty Hazer Tram System for ROHN 20/25G Towers USA Made

Glen Martin H-2 Heavy Duty Hazer Tram System for ROHN 20/25G Towers USA Made

Glen Martin H-2 Heavy Duty Hazer Tram System for ROHN 20/25G Towers USA Made
HEAVY DUTY HAZER TRAM SYSTEM. Hazers eliminate tower climbing, allow easy access to antennas, carry heavy loads, and feature quality.

Construction and easy installation on an erect tower. Never climb a tower again!

See below for details on how Hazers work. Dead Weight Load: 175 lbs. Dimensions: 44" H x 15-1/4" W.

Top & bottom plates for rotor and thrust bearing. 100' of 1/8 winch cable (for a 50' tower). All mounting hardware (stainless steel). Towers over 50' require additional cabling.

Towers equipped with a TailTwister rotor require a HR-6010 TailTwister plate. Visit our store for more Hazers & Hazer Accessories. The Hazer works like a simple elevator designed to easily raise and lower your antennas, measuring instruments. The Hazer is designed to wrap around the tower.

A pulley at the top of the tower, along with a winch. And wire rope is used to raise and lower the antenna. It's as simple as raising a flag up a flag pole. The Hazer makes servicing your antennas a cinch, even with one person! May guy wires be used with the Hazer?

A fifty foot tower will require only one set of guy wires in most cases. We suggest putting these guys at the very. Top of the tower in the few inches just above the Hazer. To lower a beam antenna, disconnect two guys by.

Completely unscrewing the turnbuckles at the ground. The guys then will drape in toward the tower. Then be lowered to the ground. Once down, the guys can be reconnected.

Imagine having a completely guyed. Tower with your antenna system parked at ground level. Never worry about storms again! Is it easy to install?

The Hazer is easily assembled on an erected tower; however, some climbing is necessary to install the pulley. Block assembly and winch cable.

If it is installed before the tower is erected, no climbing is required. Installed, the Hazer travels smoothly past tower braces and section joints. GLEN MARTIN HAZER PRODUCTS ARE PROUDLY MADE IN THE USA.

The item "Glen Martin H-2 Heavy Duty Hazer Tram System for ROHN 20/25G Towers USA Made" is in sale since Thursday, October 12, 2017. This item is in the category "Consumer Electronics\Radio Communication\Antennas\Ham, Amateur Radio Antennas". The seller is "antennapartsoutlet1" and is located in Mount Carroll, Illinois. This item can be shipped to United States, Canada, United Kingdom, China, Mexico, Germany, Japan, Brazil, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Chile, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Bangladesh, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Luxembourg, Monaco, Macao, Martinique, Nicaragua, Peru, Pakistan, Paraguay, Viet nam, Uruguay, South africa, Colombia, Barbados, Bermuda, Cayman islands, Sri lanka, Maldives, Oman, Reunion.
  • To Fit: ROHN 20 / 25 Tower, 20 / 25G ROHN Tower
  • Compatible Brand: Glen Martin Hazer
  • Brand: Glen Martin Hazer
  • Model: Hazer Tram System
  • MPN: H-2 / H2
  • Country/Region of Manufacture: United States
  • Country of Manufacture: United States

Glen Martin H-2 Heavy Duty Hazer Tram System for ROHN 20/25G Towers USA Made