Instead of the adjusting screws and plugs on the jpc-7 and pac-12, the new antenna has a sliding adjuster that makes adjusting the standing waves easy and easy. Instead of screwing the adjusting screws around to adjust the standing waves, just slide the adjusting slider with your finger. It is recommended not to add at will, otherwise the base may be damaged and safety accidents may occur, at most two extension tube on each side, otherwise the weight is too large. The picture below shows the antenna with adjusting screw insert. Note: a 3-line barron will be provided in the future, no longer with the feeder in the photo.
The processing technology of vibrator aluminum tube has been improved. At the same time, it has been changed from 28cm to 32cm. The connecting seat has been changed from the original aluminum part to copper part.
The mini-buddipole antenna is a miniature portable antenna designed for field mobile communications. Completely is made according to the original standard, can work in 2,6,10,12,15,17,20,30,40 meters, contraction after 34.5 cm long, two \ oscillator expanded for 6 meters (4.8 m), the size of the package to: 37 cm 23 cm, weight 1.8 kg, easy to carry erection convenient, after hand as long as a support bar and feeder, can set up to use, all the other parts are disposed of for you.Ground net, ground anchor this shop has sale. Impedance 50 ohm standing wave 1.0-1.2. The coil skeleton and base are made of moulded, not made by hand.
The strength is very high and there is no need to worry about damage. The coil is now wound with 1.0mm 304 stainless steel wire, which has higher strength and overcomes the weakness of the tinned copper wire. The aluminum tube is sandblasted and oxidized to black, which is very beautiful. Equipped with special black portable cloth bag, perfect protection antenna, easy to carry, more class. It is easy and fast, and can be set up by one person in 3 minutes.
The aluminum in the joint seat was replaced by copper, which is stronger and more durable. The assembly sequence of each oscillator of the antenna is as follows: connecting seat - two aluminum tubes - inductive coil - pull rod antenna. If you use a talent meter with low transmission power, do not coil the feeder into a circle, but open all the feeders, otherwise the adjustment of standing wave will be affected, and the talent meter with higher power will not matter. The first turn is on the side of the antenna near the pull rod.Count from the side with the screw of the fixed coil, and do not count the half turn with the screw. When adjusting standing wave, under the condition of the instrument, first find the lowest point of standing wave, see whether the resonance frequency is high or low, if the resonance frequency is high, the antenna is short, want to lengthen the pull rod antenna or increase the number of inductance coil, shorten the pull rod antenna or reduce the number of inductance coil. It is suggested to adjust the inductor coil and pull rod antenna on one side of the black line first instead of adjusting the oscillators on both sides. 40m band: 7.050- the red coil starts the 5th turn from the aluminum tube side, and the black coil also starts the 10th turn from the aluminum tube side. Note: the half circle with one screw does not count. The antenna of the pull rod on both sides is pulled out 7.050 standing wave 1.2-1.5. 20-meter band: 14.270-red wire coil starts from one side of the pull rod antenna for a count of 5 turns, and all 10 sections of the pull rod antenna are pulled out.
The black wire coil also counted the 11th turn from one side of the pull rod antenna, and all 10 sections of the pull rod antenna were pulled out at 8cm. Standing wave 1.0 to 1.2. 15 m band: 21.300 red wire coil 3 turns, pull rod antenna 10. The black wire coil has 3 turns, and the tie rod antenna has 9 +11cm 21.300 standing wave 1.2. 10 m band: 10 pull rod antennas.
The other pull rod antenna 10 retracts to about 7cm. Standing wave 1.2 (without inductive coil). Multi-band coils (40m-10m, material: nylon) x2pcs. Alumina tube x4pcs (black), 19×320mm.
Top 2.5m stainless steel tie rod antenna x1pcs (customized and thickened). Erect positive V copper connectors x2pcs.
Note: the new antenna will be replaced by the new magnetic ring barron instead of the plug -3 American feeder. Special black hand-held cloth bag x1pcs, shape specification 3723. Special adapter x1pcs made of aluminum for connecting the tripod. One copy of the original adjustment version of plug line for installation reference only. Please make sure it is correct.
We believe our items are so outstanding. All products are quality checked. We will be happy to resolve any issues you may have in a cordial and friendly manner. We appreciate your Postive Feedback, and will do the same in return. The item "JPC-7 Multi Band mini-buddipole HF Shortwave Outdoor Portable Antenna QRP" is in sale since Saturday, July 18, 2020.This item is in the category "Consumer Electronics\Radio Communication\Antennas\Ham, Amateur Radio Antennas". The seller is "flyxy2015" and is located in ShenZhen ,Guangdong. This item can be shipped worldwide.