MAT-30 HF Auto-tuner 120W AUTO TUNER Automatic Antenna Ham Radio For Yeasu
The interface cable is included. The operating is the same as the method of the Yeasu tuner, which is simple and convenient. The mAT-30 can work within the range of 3MHz to 54MHz. The mAT-30 connects to the radio via its CAT/LINEAR jack to control the tuning cycle;the transceivers Tune button controls the tuner.
The CAT/LINEAR jack also powers the tuner, so it requires no external power supply. The mAT-30 is specially engineered to integrate with your Yeasu FT-100/857/897/450D/891 HF radio.
Tuning is performed when the TUNE button is pushed. On the front of the transceiver and held for one second. The mAT-30 provides automatic antenna tuning across the entire. HF spectrum plus 6 meters, at power levels up to 120 watts. It will tune dipoles, verticals, Yagis, or virtually any coax-fed antenna.It will match an amazing range of antennas and impedance, far greater than some other tuners you may have considered, including the built-in tuners on many radios. The mAT-30 connects to the. On the back of the radio.
The CAT interface allows an external device such as a PC or the mAT-30 to control the FT-100/857/897/450D/891 by sending it serial commands. The mAT-30 takes advantage of this interface to simplify the tuning process --one button push is all that is needed in order to switch the radio to FM mode, reduce output power, transmit a carrier, measure the transmit frequency, and then restore the radio to its previous mode and power level! You can also start a tuning cycle manually whenever necessary. The mAT-30 has16,000 frequency memories.
When tuning on or near a previously tuned frequency, the mAT-30 uses "Memory Tune" to recall the previous tuning parameters in a fraction of a second. If no memorized settings are available, the tuner runs a full tuning cycle, storing the parameters for memory recall on subsequent tuning cycles on that frequency. In this manner, the mAT-30 "learns" as it is to the bands and frequencies as it goes. 0.1 to 120watts SSB and CW peak power, 30 watts on PSK and digital modes, and 100 watts on 6 meters.16,000 memories for instantaneous frequency and band changing. Controlled from YeasuTUNE button on radio. Works with most Yeasu radios that are FC-30, FC-40 or FC-50 compatible. Partial radio list: FT-100, FT-857, FT-897, FT-450D, FT-891.
Tuning time:0.1 to 5 seconds full tune, 0.1 seconds memory tune. 1.8 to 54.0 MHz coverage. Tunes 5 to 1500 ohm loads. For dipoles, verticals, Vees, beams, long wire or any coax-fed antenna. AN IMPORTANT WORD ABOUT POWER LEVELS.The mAT-30 is rated at 125 watts maximum power input at most. Many ham transmitters and transceivers, and virtually all amplifiers, output well over 125 watts. Significantly exceed specifications will definitely damage or destroy your mAT-30. If your tuner fails during overload, it could also damage your transmitter or transceiver.
Be sure to observe the specified power limitations. 1 x mAT-30 HF-SSB Automatic Antenna Tuner. Please allow 0.1- 0.5cm error due to manual measurement. The colors may have different as the difference display, please understand. Please check which Length and the quantity you need.
Customers satisfaction is very important to us! Please give us the opportunity to resolve any problem. We understand the concernsand frustrations you might have, and will try our best to resolve the issues.Other countries or remote area may take longer. And we can give you a satisfactory solution. However, it may delay due to industrial strike action, severe weather, custom reasons or peak seasons, such as Christmas/New Year Holidays. We care about our valued customers, and are always willing to work things out.